REDX / Products / Hydraulic filters
Hydraulic filters
A hydraulic circuit is protected by several elements in different places, each with its own job. Strainers, filters and breathers are not interchangeable.
Application and location
Around the reservoir, the pump and the lines
In the example circuit oil leaves the reservoir through a suction strainer, passes the pump and a pressure filter, works in the actuators and returns to the reservoir, often through a return filter. A breather lets air in and out as the oil level changes, and some machines add filtration outside the main circuit.
Machines differ in layout, so a position in one circuit is not a rule for another. Ask us which elements fit your machine.
Types in the range
- Suction strainers
- Suction (low-pressure) filters
- Pressure (high-pressure) filters
- Tank breathers
- Off-line (outside the circuit) filtration
Exact products and part numbers are confirmed when we identify your machine.
The circuit
The whole circuit, not just one filter
Select an element in the circuit, or in the list, to see its cross-section and what it does. Compare the wire mesh of a strainer with the pleated medium of a filter.
- Oil at low pressure (suction, return)
- Oil under pressure
- Particles in the oil
- Flow direction
Reservoir
Holds the oil, gives air and heat a chance to leave and gives some dirt time to settle. Every other element draws from the reservoir or returns oil to it.
Where: Start and end of the circuit.
In service: The reservoir is not a filter. A clean, well-closed reservoir keeps contamination out, but the oil still has to be filtered.
Reservoir breather
As the oil level rises and falls, air moves in and out of the reservoir. The breather filters the air that comes in, so airborne dust does not get into the oil. A variant that also takes moisture out of the air is a separate design and is only relevant where it is offered.
Where: On top of the reservoir.
In service: A breather that is clogged restricts the air movement, so it is checked as part of normal service.
Suction strainer
A coarse screen at the end of the suction line. It protects the pump from large pieces of debris. It is not a substitute for fine filtration: anything much smaller than the openings in the mesh passes straight through.
Where: Inside the reservoir, at the pump suction.
In service: Because it sits on the suction side, a blocked strainer starves the pump. That is why it is coarse and why it is inspected at service.
Suction filter (if fitted)
Some circuits add a filter in the suction line, ahead of the pump. Where one is used it brings finer filtration to the pump side, but the line has very little pressure difference to spare, so it is built differently from a pressure filter. Many circuits do not have one.
Where: Between reservoir and pump, only if fitted.
In service: Pressure drop across a suction filter has to stay small. Follow the machine maker's guidance for the circuit.
Pump
Draws oil from the reservoir and pushes it into the circuit. The pump is one of the components most sensitive to particles, which is what the strainer and the filters ultimately protect.
Where: Between the suction line and the pressure line.
In service: Wear in the pump shows up as lost performance, so contamination control upstream and downstream protects it.
Pressure filter
Located after the pump, it cleans the oil before it reaches the valves and actuators, whose fine clearances tolerate dirt least. The medium is pleated to give a large surface in a compact housing. This is an example position: machines differ in where, and whether, a pressure filter is fitted.
Where: Pressure line, after the pump.
In service: Flow resistance rises as the medium loads with dirt. A clogging indicator shows when the element is approaching the end of its service life.
Valve block
Directs oil to the cylinder or the motor and lets it return to the reservoir. Spools and bores have very small clearances, so dirt in the oil can make them stick or wear.
Where: After the pressure filter, before the actuators.
In service: Not a filter. It is shown because its clearances are one of the reasons the circuit is filtered.
Actuator: cylinder
Turns oil pressure into linear force. Oil entering one end pushes the piston, and oil leaving the other end returns towards the reservoir. Particles reaching the cylinder can score the rod and seals.
Where: At the working end of the circuit.
In service: Not a filter. Oil leaving it carries back whatever the cylinder has picked up.
Actuator: hydraulic motor
Turns oil flow into rotation, for example to drive a travel or swing function. As with the cylinder, the oil leaving it carries wear particles and any dirt it collected back towards the return side.
Where: At the working end of the circuit.
In service: Not a filter.
Return filter
Cleans the oil on its way back to the reservoir and holds back particles the circuit has collected, such as wear debris and dirt that entered through the cylinders. In this example circuit it is the last stage before the oil rejoins the tank. Not every machine has one.
Where: Return line, before the reservoir.
In service: As the medium fills with dirt, resistance on the return side rises. A clogging indicator shows when the element needs service.
Off-line filtration (if present in the range)
A separate small loop with its own pump that draws oil from the reservoir, filters it and sends it back, independently of the machine's working cycle. It is shown here only as an option in the example circuit.
Where: Beside the reservoir, in its own loop.
In service: Works through the same principle as other pleated filters: dirt collects on the medium and the indicator shows the state of the element.
How the flow works
Who protects what
Coarse protection
A suction strainer is a coarse screen that protects the pump from large debris. It does not replace fine filtration.
Fine filtration
Filters with pleated medium hold back finer particles. A pressure filter protects the valves and actuators; a return filter catches what the circuit picks up before the oil returns to the reservoir.
Keeping the tank clean
A breather filters the air that enters the reservoir. A drying variant exists for some designs only and is a different product.
Choosing
What matters when choosing
- Where the element sits: suction, pressure, return, tank or off-line.
- The housing, the connection and the element shape.
- The type of the indicator for the pressure drop, where the machine has one.
- The hydraulic fluid and the machine variant, since the same model can be built differently.
- The part number of the element that is fitted now.
Service
Practical service notes
- Watch the indicator for the pressure drop, if fitted, and know that cold oil can read differently from warm oil.
- Never replace a filter with a strainer or the other way round.
- Clean around the filter head before opening a housing, so dirt does not fall into the system.
- Hydraulic oil is only as clean as the way it is filled: keep the filling equipment clean.
Find filters for your machine
Tell us about the machine
To suggest the right filters we first need to identify the machine and the filters it has now. Send us as much of the list as you can.
What helps us choose
- Machine manufacturer and model
- Serial number or PIN
- Engine variant (see the engine plate)
- Part numbers of the filters currently fitted
- A photo of the machine plate and of the old filter
The button opens an e-mail with these headings ready to fill in. A model name alone is not enough to confirm a match, because the same model can come with different configurations.