Skip to content

REDX / How filtration works

How filtration works

Every filter sits where contamination would do the most harm. The demonstrations on this page follow the flow through the filter and show where each kind of contaminant ends up.

Fuel

Water and particles are separate jobs

Water drops join, fall into the bowl and leave through the drain. Solid particles settle on the medium. The fine filter then protects the injection system.

  • Fuel with particles and water
  • Filtered fuel
  • Solid particle
  • Water droplet
  • Flow direction
  • Fuel tank
  • Sediment bowl (if fitted)
  • Pre-filter + water separator
  • Water bowl — Drain (if fitted) — Water sensor (if fitted)
  • Fine filter
  • Feed pump
  • Injection system — to the engine

Example configuration — functions may be combined in one housing.

From the tank

Fuel leaves the tank carrying what it picked up on the way: a fine suspension of solid particles and tiny droplets of water. The heaviest contamination settles at the bottom of the tank, but whatever stays suspended follows the fuel into the supply line.

Sediment bowl (if fitted)

Where a machine has a separate sediment bowl, the fuel slows down inside it. Heavy particles and large drops of water sink to the bottom and stay there, so less reaches the filters. Fine particles and tiny droplets stay in the fuel and travel on. Many machines do not have this element.

Pre-filter and water separator

Inside the pre-filter the fuel passes through the pleated medium from the outside in. Solid particles are caught on the surface of the medium. Water behaves differently: tiny droplets meet on the medium and merge into larger drops (coalescence). Once a drop is heavy enough it runs down and falls into the water bowl below.

Water bowl, drain and sensor

Separated water collects in the bowl because it is heavier than fuel. Only housings designed for it have a drain to let the water out and a water sensor to signal when the bowl needs emptying. Not every pre-filter has either of them.

Fine filter

The fine filter is the last barrier before the injection system. It holds back the fine particles that the pre-filter stage may let through. That is why the two parts do different jobs: the separator deals with free water, the fine filter protects the injection components from solid particles.

Illustration of the operating principle — not a specific REDX product drawing.

Fuel filters →

Hydraulics

A circuit has several guardians

Strainer, pressure filter, return filter and breather each work in their own place with their own job.

  • Oil at low pressure (suction, return)
  • Oil under pressure
  • Particles in the oil
  • Flow direction

Example circuit — machines differ in configuration.

Reservoir

Holds the oil, gives air and heat a chance to leave and gives some dirt time to settle. Every other element draws from the reservoir or returns oil to it.

Where: Start and end of the circuit.

In service: The reservoir is not a filter. A clean, well-closed reservoir keeps contamination out, but the oil still has to be filtered.

Reservoir breather

As the oil level rises and falls, air moves in and out of the reservoir. The breather filters the air that comes in, so airborne dust does not get into the oil. A variant that also takes moisture out of the air is a separate design and is only relevant where it is offered.

Where: On top of the reservoir.

In service: A breather that is clogged restricts the air movement, so it is checked as part of normal service.

Suction strainer

A coarse screen at the end of the suction line. It protects the pump from large pieces of debris. It is not a substitute for fine filtration: anything much smaller than the openings in the mesh passes straight through.

Where: Inside the reservoir, at the pump suction.

In service: Because it sits on the suction side, a blocked strainer starves the pump. That is why it is coarse and why it is inspected at service.

Suction filter (if fitted)

Some circuits add a filter in the suction line, ahead of the pump. Where one is used it brings finer filtration to the pump side, but the line has very little pressure difference to spare, so it is built differently from a pressure filter. Many circuits do not have one.

Where: Between reservoir and pump, only if fitted.

In service: Pressure drop across a suction filter has to stay small. Follow the machine maker's guidance for the circuit.

Pump

Draws oil from the reservoir and pushes it into the circuit. The pump is one of the components most sensitive to particles, which is what the strainer and the filters ultimately protect.

Where: Between the suction line and the pressure line.

In service: Wear in the pump shows up as lost performance, so contamination control upstream and downstream protects it.

Pressure filter

Located after the pump, it cleans the oil before it reaches the valves and actuators, whose fine clearances tolerate dirt least. The medium is pleated to give a large surface in a compact housing. This is an example position: machines differ in where, and whether, a pressure filter is fitted.

Where: Pressure line, after the pump.

In service: Flow resistance rises as the medium loads with dirt. A clogging indicator shows when the element is approaching the end of its service life.

Valve block

Directs oil to the cylinder or the motor and lets it return to the reservoir. Spools and bores have very small clearances, so dirt in the oil can make them stick or wear.

Where: After the pressure filter, before the actuators.

In service: Not a filter. It is shown because its clearances are one of the reasons the circuit is filtered.

Actuator: cylinder

Turns oil pressure into linear force. Oil entering one end pushes the piston, and oil leaving the other end returns towards the reservoir. Particles reaching the cylinder can score the rod and seals.

Where: At the working end of the circuit.

In service: Not a filter. Oil leaving it carries back whatever the cylinder has picked up.

Actuator: hydraulic motor

Turns oil flow into rotation, for example to drive a travel or swing function. As with the cylinder, the oil leaving it carries wear particles and any dirt it collected back towards the return side.

Where: At the working end of the circuit.

In service: Not a filter.

Return filter

Cleans the oil on its way back to the reservoir and holds back particles the circuit has collected, such as wear debris and dirt that entered through the cylinders. In this example circuit it is the last stage before the oil rejoins the tank. Not every machine has one.

Where: Return line, before the reservoir.

In service: As the medium fills with dirt, resistance on the return side rises. A clogging indicator shows when the element needs service.

Off-line filtration (if present in the range)

A separate small loop with its own pump that draws oil from the reservoir, filters it and sends it back, independently of the machine's working cycle. It is shown here only as an option in the example circuit.

Where: Beside the reservoir, in its own loop.

In service: Works through the same principle as other pleated filters: dirt collects on the medium and the indicator shows the state of the element.

Illustration of the operating principle — not a specific REDX product drawing.

Hydraulic filters →

Engine air

Air in, dust out

Dust stays on the pleated medium. The seal decides whether all of the air really passes through it.

  • Dusty air (dirty side)
  • Clean air (clean side)
  • Dust
  • Flow

Example configuration — pre-cleaner, dust ejector and safety element exist only in some air cleaners.

Follow the air: it enters dusty on the outside of the main element, passes through the pleated medium and leaves clean on the inside. The dust does not follow it.

Dust is stopped on the outer face of the pleats and builds up there. The air passes through a thicker layer over time, so the resistance rises and the element has to be serviced. The dust stays on the dirty side.

If the main element is missing or damaged, dust can get past it. In an air cleaner with a safety element, the dust is stopped there instead of reaching the engine. It is a protection for that situation, not a substitute for changing the main element on time.

Inlet and housing

Dusty air enters the housing through the inlet and flows around the outside of the main element. This is the dirty side. Some machines add a pre-cleaner or a dust ejector here; they are options and are not part of every air cleaner. The cover can be opened so that the element can be changed.

Where: On the intake side of the engine.

In service: A cracked housing or a cover that is not closed correctly lets unfiltered air in, so closing it correctly is part of the job.

Pleated medium

The medium is folded into pleats so that a large surface fits in a small element. Dust stops on the outer face of the pleats while the air passes through the medium to the inside. A perforated core and end caps keep the pleats in shape and a gap between the pleats lets the air reach the whole surface.

Where: Between the dirty side and the clean side.

In service: As dust collects on the medium, the resistance to the airflow rises. That is the normal reason to service the element.

Seal

A gasket or rubber end cap presses the element against the housing so that dusty air cannot slip past the medium. Filtration only works when the dirty side and the clean side are separated, so the fit of the element and its seal are as important as the medium.

Where: At the open end of the element, against the housing wall.

In service: A damaged seal or an element that sits crooked is a leak path, even if the medium itself is intact.

Safety element (example configuration)

Some air cleaners have a second, inner element behind the main one. It is not meant as a second fine-filtering stage for everyday use. It protects the engine intake while the main element is removed for service and if the main element is damaged. Many air cleaners do not have one.

Where: Inside the main element, next to the outlet.

In service: It is no reason to delay changing the main element or to run on a damaged one.

Outlet to the engine

Air that has passed the medium leaves through the outlet and goes on to the engine intake. This is the clean side. The connection to the engine has to be sealed as well, because a leak downstream of the element lets dust in just as a leak at the seal does.

Where: Downstream of the element, towards the engine.

In service: Hoses, clamps and connections on the clean side are part of the filtration system.

Illustration of the operating principle — not a specific REDX product drawing.

Air filters →

Engine oil

Through the pleats to the core

Wear particles stay on the outside of the medium. When the medium fills up, a bypass valve can open as an emergency path.

  • Oil on the dirty side
  • Filtered oil
  • Wear particles
  • Flow direction

Example configuration — a bypass valve and an anti-drain-back valve exist only in some filters.

The oil enters at the base, rises on the dirty side, passes through the medium into the perforated core and leaves through the central outlet. Wear particles stay on the outer face of the medium.

As the medium fills with particles, the oil meets more resistance. In a filter with a bypass valve, the valve opens when the resistance gets too high and part of the oil flows past the medium, unfiltered, so that the engine keeps being lubricated. It is an emergency path, not a normal operating state.

Base plate and inlet holes

Oil from the engine enters through holes in the base plate, arranged around the central outlet. From there it rises on the outside of the element. This is the dirty side: the oil has not been filtered yet.

Where: At the base of the filter, against the engine filter head.

In service: Inlet and outlet are on the same side of the filter, so the filter head decides which way each one connects. The drawing shows one common arrangement.

Gasket

A rubber gasket seals the base plate against the filter head, so that oil cannot leak out at the base and the inlet cannot connect to the outlet. It sits around the inlet holes, outside them.

Where: On the underside of the base plate, in its groove.

In service: A damaged or badly seated gasket leaks oil. The sealing surface on the engine has to be clean and undamaged.

Pleated medium

Oil passes through the medium from the outside to the inside. Wear particles and combustion by-products stay on the outer face and in the depth of the medium while the oil flows on. Pleats give a large filtering surface in a small can.

Where: Between the dirty side and the core.

In service: As the medium fills with particles, the resistance to the flow rises. The engine documentation tells which filter is the right one for the engine.

Perforated core

The perforated centre tube supports the medium so that the pressure of the oil does not push the pleats together. It lets the filtered oil flow in and down towards the outlet.

Where: In the centre of the element.

In service: The oil inside the core is the filtered side.

Outlet

The filtered oil leaves through the central outlet, which is threaded onto the mounting thread of the engine. From there the oil goes on to the lubrication circuit of the engine.

Where: In the centre of the base plate.

In service: Everything inside the core and the outlet is the clean side of the filter.

Can (housing)

The can holds the element, the valves and the base plate together in one unit that is replaced as a whole. It has to withstand the pressure of the oil and the vibration of the engine.

Where: Around the element.

In service: A spin-on filter fits only engines that are built for it.

Bypass valve (if fitted)

In some filters a spring-loaded bypass valve opens when the resistance across the medium gets too high, for example with a clogged element or thick, cold oil. The valve then lets oil pass the medium so that the engine does not run without oil. The oil that goes through the bypass is not filtered at that moment. Not every filter has a bypass valve; some engines have one in the engine itself.

Where: At the top of the core, in this example.

In service: A bypass valve protects the engine from running without oil, not from dirt. It is an emergency path, not a normal operating state.

Anti-drain-back valve (if fitted)

A flexible flap at the inlet holes that closes when the engine stops, so that the filter stays filled with oil. It is a different valve from the bypass valve: it only keeps oil in the filter and has nothing to do with relieving a high resistance.

Where: On the inside of the base plate, over the inlet holes.

In service: Not every filter has one.

Replaceable cartridge

In this design a housing stays on the engine and only the filter element, the cartridge, is changed. Inside, the oil takes the same path: it enters on the outside of the medium, passes through it and leaves through the core. The seal of the cover has to be fitted correctly.

Where: In a housing on the engine or beside it.

In service: Spin-on and cartridge filters are not interchangeable. Use what the engine is built for.

Illustration of the operating principle — not a specific REDX product drawing.

Engine oil filters →

Glossary

Terms used on this site

Medium

The material that holds particles back: paper, fibre or synthetic layers, folded into pleats.

Pleats

Folds in the medium that give a large surface in a small element.

Strainer

A coarse wire screen. It protects a pump from large debris and is not a fine filter.

Coalescence

Fine water droplets joining into larger drops, which then separate from the fuel.

Pressure drop

The resistance that the flow meets in the filter. It rises as the medium fills.

Clogging indicator

A gauge or a mark that shows when the pressure drop is high, where a machine has one.

Bypass valve

A valve that opens at high resistance so that the flow continues past the medium. The oil that passes is not filtered at that moment.

Find filters for your machine

Tell us about the machine

To suggest the right filters we first need to identify the machine and the filters it has now. Send us as much of the list as you can.

What helps us choose

  • Machine manufacturer and model
  • Serial number or PIN
  • Engine variant (see the engine plate)
  • Part numbers of the filters currently fitted
  • A photo of the machine plate and of the old filter

The button opens an e-mail with these headings ready to fill in. A model name alone is not enough to confirm a match, because the same model can come with different configurations.