REDX / Products / Engine oil filters
Engine oil filters
Engine oil picks up wear particles and combustion by-products. The oil filter holds them back so the engine is lubricated with cleaner oil.
Application and location
On the engine block or a filter head
The oil filter sits in the lubrication circuit, on the engine block or on a filter head beside it. Every drop of oil that returns to the bearings has to pass it, which is why seal and fit matter as much as the medium.
Spin-on cans are replaced as a whole. Replaceable cartridges are changed inside a housing that stays on the engine.
Types in the range
- Spin-on oil filters (cans)
- Replaceable oil filter cartridges
Exact products and part numbers are confirmed when we identify your machine.
Cross-section
Through the pleats to the core
Follow the oil through a spin-on filter and compare it with a replaceable cartridge. The second scenario shows what happens when the medium fills up.
- Oil on the dirty side
- Filtered oil
- Wear particles
- Flow direction
The oil enters at the base, rises on the dirty side, passes through the medium into the perforated core and leaves through the central outlet. Wear particles stay on the outer face of the medium.
As the medium fills with particles, the oil meets more resistance. In a filter with a bypass valve, the valve opens when the resistance gets too high and part of the oil flows past the medium, unfiltered, so that the engine keeps being lubricated. It is an emergency path, not a normal operating state.
Base plate and inlet holes
Oil from the engine enters through holes in the base plate, arranged around the central outlet. From there it rises on the outside of the element. This is the dirty side: the oil has not been filtered yet.
Where: At the base of the filter, against the engine filter head.
In service: Inlet and outlet are on the same side of the filter, so the filter head decides which way each one connects. The drawing shows one common arrangement.
Gasket
A rubber gasket seals the base plate against the filter head, so that oil cannot leak out at the base and the inlet cannot connect to the outlet. It sits around the inlet holes, outside them.
Where: On the underside of the base plate, in its groove.
In service: A damaged or badly seated gasket leaks oil. The sealing surface on the engine has to be clean and undamaged.
Pleated medium
Oil passes through the medium from the outside to the inside. Wear particles and combustion by-products stay on the outer face and in the depth of the medium while the oil flows on. Pleats give a large filtering surface in a small can.
Where: Between the dirty side and the core.
In service: As the medium fills with particles, the resistance to the flow rises. The engine documentation tells which filter is the right one for the engine.
Perforated core
The perforated centre tube supports the medium so that the pressure of the oil does not push the pleats together. It lets the filtered oil flow in and down towards the outlet.
Where: In the centre of the element.
In service: The oil inside the core is the filtered side.
Outlet
The filtered oil leaves through the central outlet, which is threaded onto the mounting thread of the engine. From there the oil goes on to the lubrication circuit of the engine.
Where: In the centre of the base plate.
In service: Everything inside the core and the outlet is the clean side of the filter.
Can (housing)
The can holds the element, the valves and the base plate together in one unit that is replaced as a whole. It has to withstand the pressure of the oil and the vibration of the engine.
Where: Around the element.
In service: A spin-on filter fits only engines that are built for it.
Bypass valve (if fitted)
In some filters a spring-loaded bypass valve opens when the resistance across the medium gets too high, for example with a clogged element or thick, cold oil. The valve then lets oil pass the medium so that the engine does not run without oil. The oil that goes through the bypass is not filtered at that moment. Not every filter has a bypass valve; some engines have one in the engine itself.
Where: At the top of the core, in this example.
In service: A bypass valve protects the engine from running without oil, not from dirt. It is an emergency path, not a normal operating state.
Anti-drain-back valve (if fitted)
A flexible flap at the inlet holes that closes when the engine stops, so that the filter stays filled with oil. It is a different valve from the bypass valve: it only keeps oil in the filter and has nothing to do with relieving a high resistance.
Where: On the inside of the base plate, over the inlet holes.
In service: Not every filter has one.
Replaceable cartridge
In this design a housing stays on the engine and only the filter element, the cartridge, is changed. Inside, the oil takes the same path: it enters on the outside of the medium, passes through it and leaves through the core. The seal of the cover has to be fitted correctly.
Where: In a housing on the engine or beside it.
In service: Spin-on and cartridge filters are not interchangeable. Use what the engine is built for.
How the flow works
The path of the oil
In at the base
Oil enters through the inlet holes at the base and rises on the dirty side, around the outside of the pleated medium.
Through the medium
The oil passes through the pleats from the outside to the inside. Particles stay on the outer face of the medium.
Out through the core
The filtered oil flows into the perforated core and leaves through the central outlet. A bypass valve, where fitted, opens only as an emergency path when the resistance is too high.
Choosing
What matters when choosing
- Spin-on or cartridge, and the thread or the housing it must fit.
- The gasket size and the base plate, so the new filter seals against the head.
- Whether the filter head or the filter has a bypass valve or an anti-drain-back valve; they are different valves.
- The engine variant and the part number of the filter that is fitted now.
Service
Practical service notes
- Follow the engine maker for how to fit the gasket and how tight to turn a spin-on filter.
- Treat the bypass valve as an emergency path, not as a normal operating state.
- Change the filter together with the oil as the engine documentation says.
- Never refit a cartridge or its seal that is damaged.
Find filters for your machine
Tell us about the machine
To suggest the right filters we first need to identify the machine and the filters it has now. Send us as much of the list as you can.
What helps us choose
- Machine manufacturer and model
- Serial number or PIN
- Engine variant (see the engine plate)
- Part numbers of the filters currently fitted
- A photo of the machine plate and of the old filter
The button opens an e-mail with these headings ready to fill in. A model name alone is not enough to confirm a match, because the same model can come with different configurations.